Layout and utility locate
We mark the fence line with stakes and a string line, confirm property boundaries, and contact Colorado 811 for utility locates before any digging starts. Aluminum panels are fixed lengths, so the layout has to be exact.
Denver Fence Contractor
17 Denver neighborhoods served
Open Daily
Mon–Sun 7:00 AM–8:00 PM
Call to Book
Call (720) 697-2456
Permit Guidance
Zoning rules checked per job
What our aluminum fence installation includes
Every aluminum fence we build comes with the same core scope: layout, post setting, panels, gates, and cleanup. Here is what is covered, and what we will flag before we start if your lot needs something different.
Posts set in concrete
Aluminum posts go deep in concrete — frost depth in the Denver metro is commonly cited at about 36 inches — because a lightweight panel still needs a post that will not heave in freeze-thaw ground.
Powder-coated panels and rails
Panels are powder-coated aluminum, so the finish resists rust and does not need painting. We check the panel spec and the racking range before quoting a sloped run.
Gates with proper bracing
Aluminum gates get reinforced frames and heavy hinges. We hang the gate, test the swing, and adjust the latch before we leave. A light gate on a weak post is the most common aluminum failure.
Permit and HOA guidance
We check the Denver rules for your address — 4 feet in front of the primary facade, 6 feet behind it, zoning permit over 4 feet — and help with HOA submittals. Aluminum is usually welcome in front yards, including in historic districts, but we check per address.
Demo, haul-away, and cleanup
Old aluminum fence, concrete footings, and scrap all go in the trailer. We rake the work area, sweep the driveway, and walk the line with you before we leave.
Aluminum fence installation Denver CO: what the job actually involves
Aluminum fence installation Denver CO is the process of setting aluminum posts in concrete and hanging powder-coated picket panels between them. The panels are light, they rack to follow a slope, and they arrive in fixed lengths, so the job is mostly layout: the line has to be measured to the panel, the posts have to be plumb, and the gates have to be built to the opening.
Most Denver homeowners choose aluminum for a front yard, a pool surround, or a view lot. It looks like iron, it will not rust, and it never needs painting or staining. The honest limit is privacy: aluminum is an open fence, so it does not screen a backyard. For a rear privacy run, wood, vinyl, or composite is the better call.
How our aluminum fence installation process works
Every job follows the same four steps, whether it is a 40-foot front run in Congress Park or a pool surround in University Hills. You will know what happens each day.
01
Call
Call (720) 697-2456, Monday through Sunday, 7:00 AM to 8:00 PM. We talk through the aluminum fence, the yard, and the lot, and set a time to measure.
02
Measure & plan
We measure the line to the panel length, check the ground and the slope, note trees and roots, and confirm the height, permit, and HOA rules for your address.
03
Build
Posts go in concrete and cure, panels are racked to the grade and hung plumb, and gates are reinforced, hung, and tested. We keep the site tidy as we go.
04
Walk-through
We walk the finished aluminum fence with you, check every gate and latch, and clear the site before we leave.
Tools and methods we use on every aluminum fence
Tools & Equipment
Post hole digger and auger
Used to bore clean holes deep enough to clear the frost line. Aluminum posts are light, so the concrete footing does the structural work.
String line and level
The string line keeps the fence straight over 100 feet, and the level keeps every post plumb. A crooked post shows immediately on a rigid panel run.
Circular saw and fine-tooth blade
Aluminum cuts cleanly only with the right blade. A rough cut leaves a burr that shows through the powder coat.
Tamper and wheelbarrow
The tamper packs soil around each footing so the aluminum fence post does not shift, and the wheelbarrow moves concrete mix to the hole.
Level and square for gates
Aluminum gates are built square and hung on reinforced posts. We check the diagonal before the gate goes on the hinges, not after.
Stainless fasteners
Stainless screws and brackets hold the panels without rust streaks. Galvanized hardware can react with aluminum, so we use the right fastener for the metal.
Methods & Standards
Posts set below Denver frost depth
Frost depth in the Denver metro is commonly cited at about 36 inches, and the exact code figure for fence posts is not settled in the sources we reviewed — so we treat 36 inches as the floor, never the target, and set aluminum fence posts in concrete.
Panels racked to the grade
Aluminum panels rack — they tilt to follow a slope — so a sloped lot gets a fence that follows the ground instead of stepping in awkward jumps.
Powder coat, not paint
The finish is baked-on powder coat, so it does not peel the way paint does. A scratched panel can be touched up, but the coating itself needs no maintenance cycle.
Open pickets for views and light
Aluminum's open pickets keep the view, the light, and the air. That is the point of the material — and the reason it is the wrong choice for a privacy run.
When Denver homeowners call us for an aluminum fence
01
A front yard needs a fence that suits a period home
What we do:We measure the front run, talk through black powder-coated aluminum with brick piers or low masonry, and check the historic-district rules for the address. Aluminum reads like iron without the rust or the weight.
→ A front fence that matches the house, stays tidy, and never needs painting.
02
A pool needs a fence around it
What we do:We measure the pool surround, talk through self-closing, self-latching gates and climb-resistant picket spacing, and check the current Denver pool-barrier rule for the address before building. Our pool-fence page covers the code picture in detail.
→ A pool surround that keeps the water visible and the gate shut behind every swimmer.
03
A view lot needs a fence that does not block the view
What we do:We measure the view side, confirm the 4-foot front and 6-foot rear height rules, and build a low aluminum run that keeps the skyline or the mountains in frame while marking the lot line.
→ A boundary that protects the lot without hiding the reason the lot is worth living on.
04
A wrought-iron fence has rusted through and needs replacing
What we do:We check whether the iron can be repaired or whether replacement is the better call, then build aluminum in the same line and style. Aluminum gives the same look without the rust cycle.
→ The iron look, without the annual rust repair.
How aluminum fence installation runs in Denver
Aluminum is the rust-proof metal fence, and Denver's climate is kind to it: it does not rot in clay, it does not crack in hail the way vinyl does, and its powder coat holds up to high-altitude sun. The failure mode is the post — a lightweight panel on a shallow footing heaves in freeze-thaw ground — so the job is really about the concrete, not the metal. And the material has one honest limit: it is an open fence, so it will never give you privacy.
Neighborhoods We Serve
-
Brick homes from 1900 to 1940 around a 165-acre park. Park-facing fronts stay low and open; the solid 6-foot fence belongs at the rear. Local installers flag the heavy clay here and set posts deeper than the Denver norm. On these streets, a powder-coated aluminum fence is the usual call.
-
Cherry Creek North is the residential pocket behind the shopping district: early-1900s Craftsman and bungalow streets with small lots of 5,000 to 10,000 square feet and heavy scrape-and-rebuild. A powder-coated aluminum fence is the usual call on these streets.
-
About 80 percent of buildings date from 1900 to 1929, with the highest concentration of Denver Squares in the city. Part of the neighborhood falls in the 7th Avenue Historic District, and 7th Avenue Parkway triggers a permit at any height. These streets usually call for a powder-coated aluminum fence.
-
Settled on high ground west of the South Platte and annexed by Denver in 1896 (some histories say 1890). The Potter Highlands Historic District covers about 276 acres and 571 contributing buildings — check per address before planning a fence. On these streets, a powder-coated aluminum fence is the usual call.
-
Master-planned community on the former Stapleton airport, built mostly 2002 to 2019. The Master Community Association and sub-associations review fence designs before the city permit — two approvals, in that order. A powder-coated aluminum fence is the usual call on these streets.
Local Conditions We Plan For
-
High-altitude UV that weathers wood and vinyl
At 5,280 feet, Denver sun is stronger than at sea level. Unstained cedar turns silver-gray in a few years, and vinyl shows hail and UV wear first on the cheaper panels. For a aluminum fence, that means planning for sun and hail from the start — the material choice is the defense.
-
Freeze-thaw cycles that heave shallow posts
Denver's freeze-thaw ground lifts shallow posts within a winter or two. Frost depth is commonly cited at about 36 inches in the metro, and posts set shallower than that are the usual cause of a leaning fence. On a aluminum fence job, posts go deep in concrete so the freeze–thaw ground cannot lift them.
-
Historic-district review is block-specific
In a Denver landmark district, a fence needs a permit and a Certificate of Appropriateness at any height, and front fences must stay low and mostly open. District boundaries are block-specific — never assume a whole neighborhood is or is not in one. A aluminum fence in a landmark district needs the permit and the Certificate of Appropriateness first.
-
Chinook wind that loads solid fences
Chinook gusts on the Front Range can top 80 mph on the I-25 corridor. A solid 6-foot privacy run catches the full wind load, which is why posts, footings, and rail fastening matter more than the pickets. For a aluminum fence, that means posts, footings, and rail fastening sized for the wind load — the panels are the easy part.
What a typical aluminum fence job looks like in Denver
Aluminum fence problems we fix for Denver homeowners
Most aluminum calls start with a problem, not a wish list. Here are the four we hear most often, and how we handle each one.
Problem
A leaning run after a freeze-thaw winter
A heaved post shows immediately on a rigid aluminum panel run — the panels rack and the rails pull out of the post pockets.
Our Fix
We dig out the failed footing, reset the post deep in fresh concrete, and rehang the panels. If the panel is undamaged, you keep it.
Problem
A gate that drags or will not latch
A light aluminum gate on a weak post sags, and the latch stops meeting the post. The fix is almost always the post or the frame, not the gate itself.
Our Fix
We diagnose the cause first — post, hinges, or frame — and fix the actual problem with a reinforced frame and proper hardware, then test the swing.
Problem
Scratched or chipped powder coat
A scratched panel exposes bare aluminum, and the scratch shows against the black finish even before any corrosion starts.
Our Fix
We touch up the coating with a matching finish and check whether the panel needs replacing. A small scratch is a maintenance item, not a new fence.
Problem
A fence that does not meet historic-district rules
Aluminum is usually welcome in historic districts, but the design still has to pass Landmark review where it applies, and the front height and openness rules still bind.
Our Fix
We review the district rules for the address, measure the fence, and work out whether a design change or a new Certificate of Appropriateness brings it into compliance.
Why Denver homeowners choose aluminum fencing
Aluminum is the iron look without the rust: light, strong, and finished to last. Here is what you actually get when we build yours.
-
Will not rust
Aluminum does not rust, and the powder coat does not peel the way paint does. In Denver's clay and sprinkler spray, that is the difference between a fence that lasts and one that needs annual attention.
-
Keeps the view
Open pickets keep the skyline, the mountains, and the light. For a front yard or a view lot, that is the whole point of the material.
-
Light, strong, and low-upkeep
Aluminum panels are light enough to rack to a slope and strong enough to hold their shape in chinook wind. There is no staining, sealing, or painting cycle.
-
What aluminum fencing costs in the Denver market
Third-party market guides published in October and November 2026 put aluminum ornamental fencing at $29 to $90 per linear foot installed. Sources: NumeralQ, 26 Oct 2026; Denver Fence Contractors; Recommended.app, Nov 2026 access. Those are market ranges, not Payless Fence Company prices. Call (720) 697-2456 with your fence length and material and we will talk through a quote for your yard.
Denver fence rules to know before you build
Denver Fence Rules to Know
- 4 feet in front, 6 feet behind — aluminum suits the front — Denver caps a fence at 4 feet in front of the primary street-facing facade and 6 feet behind it. Aluminum's open pickets suit the front yard, where the rules favor low and mostly open fencing.
- Zoning permit over 4 feet — Any fence over 4 feet tall needs a Denver zoning permit; over-height requests go through the Zoning Code's over-height process.
- Colorado 811 before digging — We contact Colorado 811 for utility locates before any post hole is dug — never dig blind in a Denver yard, even for a light aluminum run.
- HOA first, city second — In an HOA neighborhood, the association approves the fence before the city permit is filed; neither approval substitutes for the other.
Rated on Google
Google ★★★★★4.9 out of 5
Rated 4.9 out of 5 from 27 Google reviews. Read the reviews on our Google Business Profile, or call (720) 697-2456 to talk about your fence.
Local experience with aluminum fences in Denver
Aluminum in Denver has to survive freeze-thaw ground, chinook wind, and high-altitude sun. We build it for those conditions: deep concrete footings, panels racked to the grade, and stainless fasteners that will not streak the finish. If your lot is in a historic district, we check the Landmark rules for the address before the build.
- Posts set deep for Denver's bentonite clay and freeze-thaw ground
- Panels racked to follow sloped lots
- Powder-coated finish with stainless fasteners
- Historic-district and HOA checks before the build
- Old fence, footings, and scrap hauled away
Rated 4.9 out of 5 on Google
Payless Fence Company is rated 4.9 out of 5 from 27 Google reviews. The aggregate covers our Denver fence work, aluminum included. Call (720) 697-2456 to talk about your aluminum fence.
★★★★★
4.9 out of 5
Based on 27 Google reviews for Payless Fence Company. We do not publish customer quotes on this page; read the reviews on Google, then call us to talk about your fence.
Call (720) 697-2456Frequently asked questions about aluminum fence installation in Denver
Real answers to the questions we hear most often about aluminum fence from local homeowners and property managers.
How much does aluminum fence installation cost in Denver?
Third-party market guides published in October and November 2026 put aluminum ornamental fencing at $29 to $90 per linear foot installed. Sources: NumeralQ, 26 Oct 2026; Denver Fence Contractors; Recommended.app, Nov 2026 access. Those are market ranges, not Payless Fence Company prices. Call (720) 697-2456 with your fence length and material and we will talk through a quote for your yard.
Is aluminum a good pool fence?
Yes — aluminum is the most common pool-fence material in Denver, because it will not rust, it keeps the pool visible, and its pickets can be spaced to resist climbing. The gates must be self-closing and self-latching. Denver's residential pool-barrier height is not settled in the code text we reviewed — secondary sources conflict between 48 and 60 inches — so we check the current rule for your address and permit before building.
How long does aluminum fence installation take in Denver?
A standard backyard run of 100 to 150 feet usually takes two to four days on site once the permit and utility locate are in hand. The permit and locate add time before the build starts, and larger perimeters, gates, and sloped or rocky yards add more. Aluminum panels go up fast once the posts are set — the posts and curing set the pace. Call (720) 697-2456 and we will talk through timing for your lot.
Do I need a permit for a aluminum fence in Denver?
Denver requires a zoning permit for any fence over 4 feet tall, and a permit at any height on a landmark property, in a historic district, or along a designated parkway. Fences 4 feet and under generally need no permit, and a like-for-like replacement of a fence that already had a permit is generally exempt when nothing changes in location, footprint, or height. Aluminum's open pickets suit the front, where the 4-foot cap usually keeps the permit out of it. Check your address before you build — historic-district and parkway rules are block-specific — and call (720) 697-2456 and we can walk through what your lot needs.
Other fence services we handle in Denver
Wrought Iron Fence Installation
Ornamental iron and steel fencing for entries, courtyards, and period homes. Pairs with a powder-coated aluminum run on the same lot.
View Wrought Iron Fence InstallationPool Fence Installation
Pool fencing checked against the rules, with self-closing, self-latching gates. Often built on the same lot as an aluminum fence.
View Pool Fence InstallationPicket Fence Installation
Low wood and vinyl picket fences for front yards and garden edges. A common companion to an aluminum fence.
View Picket Fence InstallationWood Fence Installation
Cedar and pressure-treated pine fences built for Denver clay, frost, and hail. Pairs with a powder-coated aluminum run on the same lot.
View Wood Fence InstallationFence Repair
Post, rail, picket, and gate repairs, including storm and freeze-thaw damage. Often built on the same lot as an aluminum fence.
View Fence RepairVinyl Fence Installation
Low-upkeep vinyl privacy and picket fences that hold up to Front Range sun. A common companion to an aluminum fence.
View Vinyl Fence InstallationTalk to our fence crew
Call (720) 697-2456 to talk about an aluminum fence. We answer Monday through Sunday, 7:00 AM to 8:00 PM. Have your approximate fence length, the style you are considering, and your neighborhood ready, and we can talk through the next steps on the call.
Payless Fence Company
-
Phone
(720) 697-2456 -
Address
Payless Fence Company LLC, Denver, CO 80201, US
-
Hours
Mon–Sun 7:00 AM–8:00 PM