Layout and utility locate
We mark the fence line with stakes and a string line, confirm property boundaries, and contact Colorado 811 for utility locates before any digging starts.
Denver Fence Contractor
17 Denver neighborhoods served
Open Daily
Mon–Sun 7:00 AM–8:00 PM
Call to Book
Call (720) 697-2456
Permit Guidance
Zoning rules checked per job
What our chain link fence installation includes
Every chain link fence we build comes with the same core scope: layout, post setting, fabric, gates, and cleanup. Here is what is covered, and what we will flag before we start if your lot needs something different.
Terminal and line posts in concrete
Terminal, corner, and gate posts go deep in concrete — frost depth in the Denver metro is commonly cited at about 36 inches — because chain link is only as tight as its end posts. Line posts follow on a regular spacing.
Tensioned fabric, top rail, and ties
The fabric is stretched with a tensioner so it does not sag, hung on a top rail, and tied to every line post. A loose chain link fence is a sagging one within a season.
Gates with proper bracing
Walk and drive gates get braced frames and heavy hinges. We hang the gate, test the swing, and adjust the latch before we leave. A gate that drags is the number one complaint on cheap fence jobs.
Permit and HOA guidance
We check the Denver rules for your address — 4 feet in front of the primary facade, 6 feet behind it, zoning permit over 4 feet — and help with HOA submittals. Some HOAs and historic districts restrict chain link, so we check before you commit to the material.
Demo, haul-away, and cleanup
Old chain-link fence, concrete footings, and scrap go in the trailer. Before we leave, we rake the work area, sweep the driveway, and walk the line with you.
Chain link fence installation Denver CO: what the job actually involves
Chain link fence installation Denver CO is the process of setting terminal and line posts in concrete, stretching galvanized or vinyl-coated steel fabric between them, and hanging gates on braced frames. The work is in the tension: the fabric has to be pulled tight with a tensioner and tied at every post, or it sags. Heights run 4 feet in front yards and up to 6 feet at the rear, following Denver's height rules.
Most Denver homeowners choose chain link for a dog run, a side yard, or a long perimeter where privacy is not the point. It is the lowest-cost permanent fence per foot in the Denver market guides, it does not catch wind the way a solid panel does, and hail passes through it instead of breaking it. Privacy slats or a woven screen can be added where a run needs screening.
How our chain link fence installation process works
Every job follows the same four steps, whether it is a 40-foot dog run in Berkeley or a 300-foot perimeter in University Hills. You will know what happens each day.
01
Call
Call (720) 697-2456, Monday through Sunday, 7:00 AM to 8:00 PM, and we will talk through the chain-link fence, the yard, and the lot, and set a time to measure.
02
Measure & plan
We measure the line, check the ground and the slope, note trees and roots, and confirm the height, permit, and HOA rules for your address — including whether chain link is allowed where you live.
03
Build
Posts go in concrete and cure, the fabric is tensioned and tied, and gates are braced, hung, and tested. We keep the site tidy as we go.
04
Walk-through
We walk the chain-link fence with you when the build is done, check every gate and latch, and clear the site before we leave.
Tools and methods we use on every chain link fence
Tools & Equipment
Post hole digger and auger
Used to bore clean holes deep enough to clear the frost line. Terminal posts carry the fabric tension, so their footings have to be right.
String line and level
The string line keeps the fence straight over 100 feet, and the level keeps every post plumb. A crooked line post shows as a wave in the fabric.
Wire tensioner and come-along
The tensioner pulls the fabric tight between terminal posts so it does not sag. This is the tool that separates a tight fence from a loose one.
Fence pliers and hog rings
Fence pliers twist ties and cut fabric, and hog rings bind the fabric to the tension wire. Both live on the truck for every chain link job.
Bolt cutters and fabric stretcher
Bolt cutters trim fabric to the run, and the stretcher bar holds the fabric square while it is tensioned and tied.
Gate brackets and heavy hinges
Used on gates, corners, and terminal posts to add structural strength. A bracketed gate resists racking far better than nails alone.
Methods & Standards
Posts set below Denver frost depth
Frost depth in the Denver metro is commonly cited at about 36 inches — the exact code figure for fence posts is not settled in the sources we reviewed — so 36 inches is our floor, never our target, and chain-link fence posts go in concrete.
Fabric tensioned, not draped
Chain link is stretched with a tensioner between terminal posts and tied at every line post. Draped fabric sags within a season; tensioned fabric stays tight for years.
Galvanized or vinyl-coated fabric
Galvanized fabric resists rust; vinyl-coated fabric adds a black or green coating that reads softer in a yard and resists corrosion longer. We talk through which suits the lot.
Top rail and bottom tension wire
A top rail keeps the fabric's top edge straight, and a bottom tension wire keeps the bottom from bowing out where a dog pushes against it.
When Denver homeowners call us for a chain link fence
01
A dog needs a secure run and the budget is tight
What we do:We measure the run, talk through 4- or 5-foot galvanized chain link with a walk gate, check the permit rules for the address, and build it. A bottom tension wire keeps the fabric from bowing where the dog pushes.
→ A secure yard the dog cannot push through, at the lowest per-foot cost of any permanent fence.
02
A long side lot needs a boundary, not privacy
What we do:We measure the side run, confirm the height rules for the lot, and build a chain link boundary with a gate to the alley. The fence marks the line without blocking light or air.
→ A clear boundary that does not shade the neighbor's yard or catch the wind.
03
An old chain link fence is rusted and sagging
What we do:We check whether the posts are still sound. If they are, we can re-tension the fabric and replace the failed sections; if the posts have heaved, we reset them. Our fence-repair page covers the repair-or-replace call.
→ A tight fence again, without paying for a full replacement if the posts are good.
04
A backyard needs screening without a solid wall
What we do:We build the chain link run and add privacy slats or a woven screen, which block the view while letting wind through. Slats also give a dog less to see and bark at.
→ Privacy where you want it, without the wind load of a solid 6-foot panel.
How chain link fence installation runs in Denver
Chain link is the fence that Denver's weather bothers least. Hail passes through it, wind passes through it, and galvanized steel does not rot in bentonite clay. The failure mode is different: a shallow terminal post heaves in freeze-thaw ground, the fabric goes slack, and the whole run sags. So the job is really about the posts — deep concrete footings and proper tension — and the fabric is the easy part.
Neighborhoods We Serve
-
A former smelter company town of small worker cottages, cut by I-25 and I-70. Many homes back onto freeway embankments or industry, and the western edge sits in South Platte River floodplain — verify per lot. On these streets, a chain-link fence is the usual call.
-
Post-war brick ranches from the 1940s and 1950s, mostly with fenced back yards already. Heavy clay holds water against posts, and detached garages and alleys shape most rear fence lines. A chain-link fence is the usual call on these streets.
-
Platted in 1885 with lots twice the standard Denver size. The Montclair Historic District, designated in 1975, covers only the central heart — Landmark review applies inside it, and period iron and masonry suit the front streetscape. These streets usually call for a chain-link fence.
-
Modest 1950s brick ranches subdivided in the early 1950s. Several homes back directly onto Ash Grove Park or Cook Park with private gates — a park-gate fence is a documented feature here. On these streets, a chain-link fence is the usual call.
-
Victorian and Queen Anne homes from the 1870s to 1890s on narrow lots. Part of Baker is a Denver landmark district, where a fence needs a permit at any height and front fences must stay low and mostly open — check per address. A chain-link fence is the usual call on these streets.
Local Conditions We Plan For
-
Freeze-thaw cycles that heave shallow posts
Denver's freeze-thaw ground lifts shallow posts within a winter or two. Frost depth is commonly cited at about 36 inches in the metro, and posts set shallower than that are the usual cause of a leaning fence. For a chain-link fence, that means posts set deep in concrete — shallow footings are the first thing we check.
-
Chinook wind that loads solid fences
Chinook gusts on the Front Range can top 80 mph on the I-25 corridor. A solid 6-foot privacy run catches the full wind load, which is why posts, footings, and rail fastening matter more than the pickets. On a chain-link fence job, Chinook gusts are part of the footing plan, not an afterthought.
-
Hail Alley — the 8 May 2017 storm cost $2.3 billion insured
Denver sits in Hail Alley, with 7 to 9 hail days a year. The 8 May 2017 storm caused $2.3 billion in insured losses across the metro. Vinyl is the most hail-vulnerable fence material; wood and metal fare better. A chain-link fence has to be planned for Hail Alley — the material either takes a stone or it does not.
-
Historic-district review is block-specific
In a Denver landmark district, a fence needs a permit and a Certificate of Appropriateness at any height, and front fences must stay low and mostly open. District boundaries are block-specific — never assume a whole neighborhood is or is not in one. For a chain-link fence, we check the district boundary for your address before we quote.
What a typical chain link fence job looks like in Denver
Chain link fence problems we fix for Denver homeowners
Most chain link calls start with a problem, not a wish list. Here are the four we hear most often, and how we handle each one.
Problem
Sagging fabric between posts
Loose fabric sags, and a sagging run looks neglected and lets a dog push under it. The cause is almost always a heaved terminal post or fabric that was never tensioned properly.
Our Fix
We reset the failed posts in fresh concrete and re-tension the fabric with a tensioner. If the fabric is rusted through, we replace the failed sections.
Problem
Rusted fabric at the ground line
Galvanized fabric rusts where it sits in wet soil and sprinkler spray, especially in clay that holds water against the base.
Our Fix
We replace the rusted sections and talk through vinyl-coated fabric, which resists corrosion longer. Keeping soil and mulch off the bottom wire slows the next round of rust.
Problem
A gate that drags or will not latch
A dragging gate usually means a leaning gate post or a frame that has racked. Keep forcing it and the hinges pull out of the post.
Our Fix
We diagnose the cause first — post, hinges, or frame — and fix the actual problem, then test the swing and the latch.
Problem
A fence that does not meet HOA or historic-district rules
Some HOAs and historic districts restrict chain link, especially in front yards. A fence built to the wrong spec can draw a violation notice.
Our Fix
We review the HOA or district rules, measure the fence, and work out whether a material swap, a height adjustment, or a new submittal brings it into compliance.
Why Denver homeowners choose chain link fencing
Chain link is the practical fence: the lowest per-foot cost, the toughest in hail and wind, and the easiest to repair. Here is what you actually get when we build yours.
-
Lowest per-foot cost
Chain link costs less per foot than any other permanent fence in the Denver market guides. For a long perimeter or a dog run, the difference against wood or vinyl is large.
-
Hail and wind pass through it
Chain link does not catch wind the way a solid panel does, and hail passes through the fabric instead of breaking it. The 8 May 2017 storm that cost $2.3 billion insured barely touched a chain link fence.
-
Repairable section by section
When a section rusts or a post heaves, we replace that section. You do not replace the whole fence for one bad run.
-
What chain link fencing costs in the Denver market
Third-party market guides published in October and November 2026 put galvanized chain-link fencing at $15 to $35 per linear foot installed. Published Denver ranges conflict — NumeralQ (26 Oct 2026) shows $15.00 to $22.15, while Great Neighbor Fence (5 Nov 2026) shows $25 to $35 — so treat the full span as the market range. Sources: NumeralQ, 26 Oct 2026; Great Neighbor Fence, 5 Nov 2026; HomeServicesPros, Nov 2026. Those are market ranges, not Payless Fence Company prices. Call (720) 697-2456 with your fence length and material and we will talk through a quote for your yard.
Denver fence rules to know before you build
Denver Fence Rules to Know
- 4 feet in front, 6 feet behind — and check chain link first — Denver caps a fence at 4 feet in front of the primary street-facing facade and 6 feet behind it. Some HOAs and historic districts restrict chain link, so check the material rules before you commit.
- Zoning permit over 4 feet — Denver requires a zoning permit for any fence over 4 feet tall. Over-height requests go through the Zoning Code's over-height process — most chain-link runs stay under it.
- Colorado 811 before digging — Before any post hole is dug, we contact Colorado 811 for utility locates; never dig blind in a Denver yard.
- HOA first, city second — In HOA neighborhoods, the association approves the fence before the city permit is filed; neither approval substitutes for the other — and some HOAs restrict chain link.
Rated on Google
Google ★★★★★4.9 out of 5
Rated 4.9 out of 5 from 27 Google reviews. Read the reviews on our Google Business Profile, or call (720) 697-2456 to talk about your fence.
Local experience with chain link fences in Denver
Chain link in Denver is a posts-and-tension job: deep concrete footings in bentonite clay, fabric pulled tight, and gates braced for daily use. We build it for dog runs, side lots, and long perimeters where privacy is not the point — and we will tell you plainly when a solid fence would serve the lot better.
- Posts set deep for Denver's bentonite clay and freeze-thaw ground
- Fabric tensioned with a tensioner, not draped
- Galvanized or vinyl-coated fabric matched to the lot
- Gates braced and hung to swing clean
- Old fence, footings, and scrap hauled away
Rated 4.9 out of 5 on Google
Payless Fence Company is rated 4.9 out of 5 from 27 Google reviews. We show the aggregate here; the individual reviews live on Google. Call (720) 697-2456 to talk about your chain-link fence.
★★★★★
4.9 out of 5
Based on 27 Google reviews for Payless Fence Company. We do not publish customer quotes on this page; read the reviews on Google, then call us to talk about your fence.
Call (720) 697-2456Frequently asked questions about chain link fence installation in Denver
The questions we hear most often about chain-link fence, answered for local homeowners and property managers.
How much does chain link fence installation cost in Denver?
Third-party market guides published in October and November 2026 put galvanized chain-link fencing at $15 to $35 per linear foot installed. Published Denver ranges conflict — NumeralQ (26 Oct 2026) shows $15.00 to $22.15, while Great Neighbor Fence (5 Nov 2026) shows $25 to $35 — so treat the full span as the market range. Sources: NumeralQ, 26 Oct 2026; Great Neighbor Fence, 5 Nov 2026; HomeServicesPros, Nov 2026. Those are market ranges, not Payless Fence Company prices. Call (720) 697-2456 with your fence length and material and we will talk through a quote for your yard.
Can chain link give me privacy?
On its own, no — chain link is see-through. Privacy slats or a woven screen threaded through the fabric block the view while still letting wind through, which is why slatted chain link is common on Denver dog runs and side lots. For full privacy, a solid wood, vinyl, or composite fence is the better call.
How long does chain link fence installation take in Denver?
A standard 100- to 150-foot backyard run usually takes two to four days on site once the permit and utility locate are in hand. Before the build starts, the permit and locate add time, and larger perimeters, gates, and sloped or rocky yards add more. Chain link goes up fast once the posts are set — the posts and curing set the pace. Call (720) 697-2456 to talk through timing for your lot.
Do I need a permit for a chain link fence in Denver?
In Denver, a fence over 4 feet tall needs a zoning permit, and so does a fence at any height on a landmark property, in a historic district, or along a designated parkway. Fences at 4 feet and under generally need no permit; a like-for-like replacement of a fence that already had a permit is generally exempt when nothing changes in location, footprint, or height. Most chain-link runs stay under the trigger, but the rear privacy run is the usual exception. Before you build, check your address — historic-district and parkway rules are block-specific — and call (720) 697-2456 and we can walk through what your lot needs.
Other fence services we handle in Denver
Dog Fence Installation
Physical fences and dog runs that keep dogs in and the yard usable. Pairs with a chain-link perimeter on the same lot.
View Dog Fence InstallationWood Fence Installation
Cedar and pressure-treated pine fences built for Denver clay, frost, and hail. Often built on the same lot as a chain-link fence.
View Wood Fence InstallationFence Repair
Post, rail, picket, and gate repairs, including storm and freeze-thaw damage. A common companion to a chain-link fence.
View Fence RepairCommercial Fencing
Perimeter, security, and HOA fencing for businesses and properties. Pairs with a chain-link perimeter on the same lot.
View Commercial FencingPrivacy Fence Installation
Full-height 6-foot privacy runs for backyards, alleys, and patios. Often built on the same lot as a chain-link fence.
View Privacy Fence InstallationGate Installation
Manual walk and driveway gates, braced and hung to swing clean. A common companion to a chain-link fence.
View Gate InstallationTalk to our fence crew
Call (720) 697-2456 to talk about a chain link fence. We answer Monday through Sunday, 7:00 AM to 8:00 PM. Have your approximate fence length, the height you need, and your neighborhood ready, and we can talk through the next steps on the call.
Payless Fence Company
-
Phone
(720) 697-2456 -
Address
Payless Fence Company LLC, Denver, CO 80201, US
-
Hours
Mon–Sun 7:00 AM–8:00 PM